-
Which two commands correctly verify whether port security has been configured on portFastEthernet 0/12on a switch？（）
A . SW1#show swithport port-security interface FastEthernet 0/12
B . SW1# show swithport port-secure interface FastEthernet 0/12
C . SW1# show port-secure interface FastEthernet 0/12
D . SW1#show running-config
-
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch?（）
A . SW1#show swithport port-security interface FastEthernet 0/12
B . SW1# show swithport port-secure interface FastEthernet 0/12
C . SW1# show port-secure interface FastEthernet 0/12
D . SW1#show running-config
-
A new LPAR has been created that needs SAN attached disk for a database. After AIX has been installed, the fibre cables are attached to the adapters. How should the administrator configure the disks?（）
A . Run 'mkdev' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks.
B . Run 'mkpath' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks.
C . Run 'chpath' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks.
D . Run 'cfgmgr' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks.
-
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）
A . 1
B . 10
C . 1562
D . 64000
E . 128000
-
Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A . The interface actively attempts to convert the link to a trunk link.
B . The interface is put into permanent trunking mode but prevented from generating DTP frames.
C . The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D . The interface is put into a passive mode， waiting to convert the link to a trunk link.
E . None of the other alternatives apply
-
Switch R1 has been configured with Private VLANs. With that type of PVLAN port should the default gateway be configured？（）
A . Trunk
B . Isolated
C . Primary
D . Community
E . Promiscuous
F . None of the other alternatives apply
-
Refer to the exhibit. Based on the configuration shown, which queuing mechanism has been configured on interface serial 1/0?（）https://assets.asklib.com/images/image2/2018072409525852319.jpg
A . PQ
B . CQ
C . WFQ
D . LLQ
E . CBWFQ
-
HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？ （）
A . HSRP provides redundancy and fault tolerance
B . HSRP allows one router to automatically assume the function of the second router if the second router fails
C . HSRP allows one router to automatically assume the function of the second router if the second router starts
D . HSRP provides redundancy and load balancing
-
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch？（）
A . SW1#show swithport port-security interface FastEthernet 0/12
B . SW1# show swithport port-secure interface FastEthernet 0/12
C . SW1# show port-secure interface FastEthernet 0/12
D . SW1#show running-config
E . SW1#show port-security interface FastEthernet 0/12
-
Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? （）https://assets.asklib.com/images/image2/2018073108583876318.png
A . Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B . Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C . Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D . All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
-
Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1？（）https://assets.asklib.com/images/image2/2018073011483760789.jpg
A . Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAs
B . No redistributed routes can appear in Area 1, only summary routes
C . Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs
D . Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSA
-
A new LPAR has been created that needs SAN attached disk for a database. After AIX has been installed， the fibre cables are attached to the adapters. How should the administrator configure the disks？（）
A . Run ’mkdev’ to force the FC adapter to log into the SAN， have the SAN LUNs zoned to the server， run ’cfgmgr’ to discover and configure the disks.
B . Run ’mkpath’ to force the FC adapter to log into the SAN， have the SAN LUNs zoned to the server， run ’cfgmgr’ to discover and configure the disks.
C . Run ’chpath’ to force the FC adapter to log into the SAN， have the SAN LUNs zoned to the server， run ’cfgmgr’ to discover and configure the disks.
D . Run ’cfgmgr’ to force the FC adapter to log into the SAN， have the SAN LUNs zoned to the server， run ’cfgmgr’ to discover and configure the disks.
-
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）
A . For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.
B . For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.
C . Direct inter-vlan communication does not require OSPF
D . OSPF cannot be used if router-on-a-stick is configured on the router
-
HSRP has been configured between two Company devices. What kind of message does an HSRP configured router send out every 3 seconds？（）
A . Retire
B . Coup
C . Resign
D . Send
E . Hello
-
An SVI has been configured on a device. Which two statements are true about a switched virtualinterface （SVI）？（）
A . An SVI is normally created for the default VLAN （VLAN1） to permit remote switchadministration
B . Multiple SVIs can be associated with a VLAN
C . SVI is another name for a routed port
D . An SVI is created by entering the no switchport command in interface configuration mode
E . An SVI provides a default gateway for a VLAN
-
A router has been configured with an EIGRP variance of 3. Which of the following statements istrue？（）
A . An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2
B . The successor route will end up in the routing table， and so will any route with a metric at mostthree times greater than the value of the successor’s metric
C . EIGRP will only advertise routes that are within three hops of the current router
D . The successor route will end up in the routing table， and so will any route with a metric at leastone third the value of the successor’s metric
E . The best three routes with equal cost paths will end up in the routing table
F . The successor route will be any route with three times the value of the advertised distance
-
Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）
A . Trunk
B . Isolated
C . Primary
D . Community
E . Promiscuous
F . None of the other alternatives apply
-
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? （）https://assets.asklib.com/images/image2/201807301401135173.jpg
A . Router A will prefer the path through router B for network 172.20.0.0
B . Router A will prefer the path through router C for network 172.20.0.0
C . Packets from router D will prefer the path through router B for networks advertised by router A
D . Packets from r outer D will prefer the path through router C for networks advertised by router A
-
Switch R1 has been configured with the root guard feature. What statement is true if the spanning tree enhancement Root Guard is enabled？ （）
A . If BPDUs are not received on a non-designated port， the port is moved into the STP loop- inconsistent blocked state
B . IF BPDUs are received on a PortFast enabled port， the port is disabled.
C . If superior BPDUs are received on a designated port， the interface is placed into the root- inconsistent blocked state.
D . If inferior BPDUs are received on a root port， all blocked ports become alternate paths to the root bride.
-
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）
A . There is an error in the router DRAM.
B . Te IOS image is corrupt.
C . The configuration register is set to 0x2142.
D . The TFTP server that contains the router configuration file is unreachable.
E . A boot system configuration command has placed the router into setup mode.
-
An SVI has been configured on a device. Which two statements are true about a switched virtual interface （SVI）？（）
A . An SVI is normally created for the default VLAN （VLAN1） to permit remote switch administration.
B . Multiple SVIs can be associated with a VLAN.
C . SVI is another name for a routed port.
D . An SVI is created by entering the no switchport command in interface configuration mode.
E . An SVI provides a default gateway for a VLAN.
-
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）
A . R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1
B . R1 can send IP packets to R2, but R2 cannot send IP packets to R1
C . R2 no longer learns EIGRP routes from R1 for routes not connected to R1
D . R1 no longer replies to R2's Query messages
E . R2n o longer sends to R1 Query message
-
A new LPAR has been created that needs SAN attached disk for a database. After AIX has been installed, the fibre cables are attached to the adapters.How should the administrator configure the disks？（）
A.Run ‘mkdev‘ to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run ‘cfgmgr‘ to discover and configure the disks.
B.Run ‘mkpath‘ to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run ‘cfgmgr‘ to discover and configure the disks.
C.Run ‘chpath‘ to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run ‘cfgmgr‘ to discover and configure the disks.
D.Run ‘cfgmgr‘ to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run ‘cfgmgr‘ to discover and configure the disks.
