-
While using virtualization to share SAN adapters on a server, how does Node Port ID Virtualization (NPIV) differ from Virtual SCSI (vSCSI) related to the use of multipathing software?（）
A . NPIV and vSCSI both require multipathing in VIO Server only.
B . NPIV requires multipathing software on client LPARs, vSCSI requires multipathing software on VIO Server.
C . NPIV requires multipathing software on VIO Server, vSCSI requires multipathing software on client LPARs.
D . NPIV requires multipathing and MPIO software on VIO Server LPARs, vSCSI requires multipathing software on VIO Server and MPIO on client LPARs.
-
What is the result of entering the command port-channel load-balance src-dst-ip on an EtherChannel link？ （）
A . Packets are distributed across the ports in the channel based on both the source and destination MAC addresses.
B . Packets are distributed across the ports in the channel based on both the source and destination IP addresses.
C . Packets are balanced across the ports in the channel based first on the source MAC address， then on the destination MAC address， then on the IP address.
D . Packets are distributed across the access ports in the channel based first on the source IP address and then the destination IP addresses.
-
Vessels wishing to communicate with the Port Health Officer should do（）on VHF Channel 14.
A . so
B . that
C . this
D . same
-
Your vessel is crossing a narrow channel.A vessel to port is within the channel and crossing your course.She is showing a black cylinder.What is your responsibility?（）
A . hold your course and speed
B . sound the danger signal
C . begin an exchange of passing signals
D . do not cross the channel if you might impede the other vessel
-
A virtual port channel （vPC） allows links that are physically connected to two different Cisco Nexus devices to appear as a single port channel to a third device. Which are the mandatory steps for configuring vPC？ （）
A . Enable feature vPC
B . Define domains
C . Establish peer keepalive connectivity
D . Create a peer link
E . Configure the peer link as a trunk port
F . Create port channels and vPCs
G . Define port channel load-balancing method
H . Make sure configurations are consistent
-
Which three are valid methods to monitor and trend SAN port channels with DCNM？（）
A . use summary view in the device manager
B . from the DCNM-SAN client， view ISLs in real time from the Performance drop-down list
C . for each port channel， select Monitor Continually
D . configure traps for each port channel to utilize RMON
E . set up flows with the DCNM-SAN client and use the Performance Manager web client for performance collectio
-
n a virtual port channel （vPC） configuration， VRRP exhibits which characteristic？ （）
A . VRRP does not work with vPC due to industry standard requirements
B . VRRP works with vPC in traditional active/standby modes
C . VRRP works with vPC in an active/active mode
D . VRRP work with vPC as long as vPC peer-gateway is configured to address non-standard replies to the physical MAC addre
-
Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true？ （）
A . The bring up protocol automatically detects and overrides any misconfiguration.
B . You can manually configure channel groups， or they can be automatically created.
C . Changes in configuration to the SAN port channel interface must also be made to all members of the channel group.
D . The port channel protocol uses the exchange fabric parameters command to communicate across peer ports in an ISL.
E . The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.
-
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）
A . An interface ’san-port-channel’ in NXOS
B . An interface ’port-channel’ in NXOS
C . An interface ’port-channel’ with ’mode fc’ configured
D . An interface ’fc-port-channel’ in NXOS
-
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
A . Only to Cisco Fibre Channel switches
B . Only to Cisco Fibre Channel switches in NPIV mode
C . To any Fibre Channel switch
D . Directly to storage arrays
E . Only to Nexus Switche
-
You are underway and approaching a bend in the channel where vessels approaching from the opposite direction cannot be seen．You should sound（）.
A . one blast，4 to 6 seconds in duration
B . three blasts，4 to 6 seconds in duration
C . one continuous blast until you are able to see around the bend
D . one blast，8 to 10 seconds in duratio
-
A customer has a Fibre Channel switch residing in a configuration where both production and test data coexist. Which of the following is the simplest method for ensuring that the two types of data do not flow through the same port?（）
A . VLAN
B . zoning
C . trunking
D . LUN masking
-
Which two characteristics are most typical of a SAN？ （）
A . NICs are used for network connectivity.
B . Servers request specific blocks of data.
C . Storage devices are directly connected to servers.
D . A fabric is used as the hardware for connecting servers to storage devices.
E . The TCO is higher because of the cost of director class storage switches.
-
After configuring FabricPath， the following appears in the syslog： %STP-2-L2GW_BACKBONE_BLOCK： L2 Gateway Backbone port inconsistency blocking port port-channel100 on VLAN0010. What is the cause of this message？ （）
A . STP must be disabled； message indicates that STP is enabled.
B . STP is misconfigured； root guard must be disabled.
C . An inferior BPDU is received on a Cisco FabricPath edge port.
D . A superior BPDU is received on a Cisco FabricPath edge port.
-
Which statement about SAN port channels configured on Cisco Nexus 5000 Series Switches is true？（）
A . A single SAN port channel can have both Fibre Channel and virtual Fibre Channel interfaces.
B . SAN port channels can include up to 16 interfaces.
C . SAN port channels distribute traffic across all links in the port channel when source ID and destination ID load balancing are used.
D . The links in SAN port channels can be connected to different sets of switches.
E . The On mode of operation means ports only operate as part of a SAN port channel or remain inactive.
-
On both the IBM SAN764B and the IBM SAN384B Fiber Channel Directors, all of the followingSmall Form Pluggable plus (SFP+) optical transceivers are supported EXCEPT:（）
A . 1Gbps+
B . 2Gbps+
C . 4Gbps+
D . 8Gbps+
-
Flex Links are a pair of a Layer 2 interfaces (switchports or port channels), where one interface is configured to act as a backup to the other. Which two statements are correct regarding Flex Links?（）
A . An interface can only belong to single Flex Links.
B . An interface can belong to multiple Flex Links.
C . Flex Links operate only over single pairs of links.
D . Flex Links automatically disable STP so no BPDUs are propagated.
-
While using virtualization to share SAN adapters on a server, how does Node Port ID Virtualization (NPIV) differ from Virtual SCSI (vSCSI) related to the use of multipathing software?（）
A . NPIV andvSCSI both require multipathing in VIO Server only.
B . NPIV requiresmultipathing software on client LPARs, vSCSI requires multipathing software on VIO Server.
C . NPIV requiresmultipathing software on VIO Server, vSCSI requires multipathing software on client LPARs.
D . NPIV requiresmultipathing and MPIO software on VIO Server LPARs, vSCSI requires multipathing software on VIO Server and MPIO on client LPARs.
-
Which two characteristics are most typical of a SAN? （）
A . NICs are used for network connectivity.
B . Servers request specific blocks of data.
C . Storage devices are directly connected to servers.
D . A fabric is used as the hardware for connecting servers to storage devices.
E . The TCO is higher because of the cost of director class storage switches.
-
You are crossing a narrow channel in a 15-meter vessel when you sight a tanker off your port bow coming up the channel. Which statement is TRUE? （）
A . Yours is the give-way vessel because it is less than 30 meters long
B . You shall not impede the safe passage of the tanker
C . The tanker is the stand-on vessel because it is to port of your vessel
D . The tanker is the stand-on vessel because it is the larger of the two vessel
-
Preferred channel marks are colored with（）．
A . black and green bands
B . red and green bands
C . red and yellow bands
D . yellow and green band
-
Using FTP passive mode， after the client opens thecommand channel （port 21） to the FTP server and requests passive mode， what will be the next step？ （）
A . The FTP server sends back an acknowledgment （ACK） to the client
B . The FTP server allocates a port touse for the data channel and transmit that port number to the client
C . The FTP server opens the data channel to the client using the port number indicated by the client
D . The FTP client opens the data channel to the FTP server on Port 20
E . The FTP client opens the datachannel to the FTP server on Port 21
-
Port of destination is the port where goods are shipped and depart.
-
73. Entering from sea, a daymark on the port side of the channel would be indicated on a chart by a ____.
