The crank pin journal is provided with large bores for （）.

相似题目

• The locking pin that joins the parts of a detachable link is held in position by（）.

  A . a tack weld B . the self-locking characteristics of its taper C . a cotter pin D . a lead plug

  查看最佳答案

• Each crank is made up of two crank webs joined by a common（） to which the bottom endbearing is fitted.

  A . throw B . crankshaft C . crankpin D . crosshead

  查看最佳答案

• Which is the correct description of a pinned buffer in the database buffer cache（）

  A . The buffer is currently being accessed. B . The buffer is empty and has not been used. C . The contents of the buffer have changed and must be flushed to the disk by the DBWn process.  D . The buffer is a candidate for immediate aging out and its contents are synchronized with the block contents on the disk.

  查看最佳答案

• Engine （） refers to the relative time of position of crank, at which each operation during the cycle is commenced and is completed.

  A . timing B . power C . firing order D . dead center

  查看最佳答案

• A diesel engine is turned at normal cranking speed and no ignition occursThis could be the result of （）

  A . low lube oil temperature B . low starting air temperature C . air bubbles in the fuel oil system D . water in the starting air system

  查看最佳答案

• What is the crank angle between any two crank throws in the firing order of a four-stroke/cycle, in line, eight cylinder diesel engine?（）

  A . 45 B . 60 C . 90 D . 100

  查看最佳答案

• The crankshaft is of the semi built type, with the journal （） the forged or cast steel crank throws.

  A . being shrunk into B . to be shrunk into C . to be shrunk with D . shrinking into

  查看最佳答案

• Generally the gudgeon pin is fully floating in both connecting rod small end and （）.

  A . the crosshead B . the crankshaft C . large end D . the piston bosse

  查看最佳答案

• On a medium-speed main propulsion diesel engine, the crank-pin or crank journal bearings receive lubricating oil from （）.

  A . a spindle lubricator B . an oil jet C . internal splashing D . drilled passages in the crankshaft

  查看最佳答案

• The load on the crosshead pin is always （）, so it is the （）half of the bearing which is subject to wear.

  A . upwards；top B . upwards；bottom C . downwards；top D . downwards；bottom

  查看最佳答案

• A journal kept by the officer of the watch in which day to day happenings are recorded regarding the deck department is the（）.

  A . cargo record book B . deck rough log C . bell book D . Official Logbook

  查看最佳答案

• A diesel engine cranks properly during starting but immediately stallsWhich of the following systems is most likely at fault?（）

  A . Hydraulic starting B . Electric starting C . Ignition D . Fuel

  查看最佳答案

• When an air started, four-stroke/cycle diesel engine is being cranked, the starting air is admitted to each cylinder during what would normally be the（）

  A . intake stroke B . compression stroke C . power stroke D . exhaust stroke

  查看最佳答案

• The gudgeon pin is carried in （） in the piston skirt.

  A . the bearing B . the crosshead C . bosses D . bridge

  查看最佳答案

• Lubricating oil is supplied to the crank-pin bearings in a marine diesel engine by （）.

  A . internal crankshaft passages B . immersion in oil C . splash lubrication D . injection lubricatio

  查看最佳答案

• The position of the piston parts in relation to each other is secured by means of （） and a dowel pin in the crown.

  A . bosses B . through bolts C . machine-turned recesses D . long stud

  查看最佳答案

• （） clearances in the main or crank pin bearings will sometimes be indicated by loss of pressure in the lubricating system before any bearing knock is heard.

  A . Too larger B . Too smaller C . Excess D . Excessive

  查看最佳答案

• Each journal and pin should be examined for （） and grooving.

  A . bridges B . recesses C . rears D . ridging

  查看最佳答案

• 1. Make the choice(s) that can best answer the question.What is a reading journal?

  查看最佳答案

• The journal entry to record inventory costs and direct-material variances for the month of February is

  A．Cutting Department Direct Material Control 342,000 Direct Material Variances 4,500 Work in Process—Cutting Department 337,500 B．Work in Process—Cutting Department 337,500 Direct Material Variances 4,500 Cutting Department Direct Material Control 342,000 C．Work in Process—Cutting Department 342,000 Direct Material Variances 4,500 Cutting Department Direct Material Control 337,500 D．Work in Process—Cutting Department 341,250 Direct Material Variances 750 Cutting Department Direct Material Control 342,000

  查看最佳答案

• Is it proper for the government to ______ public opinion through self-serving, onesided journalism？

  A．touch B．hunt C．sway D．proceed

  查看最佳答案

• It can be inferred from the passage that the Lancet is a journal on______.

  A．evolution B．medicine C．economy D．sports

  查看最佳答案

• Journalizing is the process to record transactions in a __________.

  查看最佳答案

• Posting is the transfer of journal entry information to the ledger.

  查看最佳答案