Which command shows dump components and controls live dump attributes？（）  

相似题目

• Which command shows your active Telnet connections？（）

  A . show session B . show cdp neighbors C . show users D . show queue

  查看最佳答案

• After a system has rebooted from a system crash, which of the following commands should be run to find the location of the dump?（）

  A .  lsvg -l rootvg  B .  sysdumpdev -e  C .  sysdumpdev -L  D .  cd /var/adm/ra

  查看最佳答案

• Which command will allow an administrator to view the primary and secondary dump devices？（）  

  A . sysdumpdev -l B . dumpmgr -ALl C . lsdev -Cc dump D . diag -dump=show

  查看最佳答案

• Which of the following commands should be used to assure that a dump can be forced using the reset button on a system without a key switch?（）

  A . sysdumpdev -k  B . sysdumpdev -L  C . sysdumpdev -K  D . sysdumpdev -P

  查看最佳答案

• Which statement best describes what is depicted in the show command output？（）

  A .  IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command. B .  The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state. C .  IGMP snooping has been disabled on the VLAN 120 SVI. D .  IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode. E .  IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.

  查看最佳答案

• Which command shows system hardware and software version information？（）

  A . show configuration B . show environment C . show inventory D . show platform E . show versio

  查看最佳答案

• Which of the following kdb commands is used to obtain a stack trace from a dump? （）

  A .  trb  B .  his  C .  f  D .  trace

  查看最佳答案

• Which of the following commands should be used to check whether a system dump is valid and readable?（）

  A .  kdb  B .  snap -d  C .  dbx -vmcore  D .  od /dev/sysdumpdev

  查看最佳答案

• After the LED display is flashing 888 and the system is rebooted, which of the following commands should be used to gather dump information?（）

  A . snap  B . errpt  C . kdb  D . trace

  查看最佳答案

• Which command will allow an administrator to view the primary and secondary dump devices?（）

  A . sysdumpdev -l B . dumpmgr -ALL C . lsdev -Cc dump D . diag -dump=show

  查看最佳答案

• A system administrator needs to configure dump devices for the system. Which command would be used to estimate the size required for a dump device？（）

  A . lsdev B . chdev C . sysdumpdev D . sysdumpstart

  查看最佳答案

• The man page for command shows the following syntax: The man page for command shows the following syntax: command [ -a -b ] Which of the following statements is true regarding this entry?（）

  A . Either the -a or flag -b may be used, but not both. B . If the flag -a is used then the flag -b also must be used. C . One of the -a or -b flags must be used, but not both at the same time. D . Both the flags may be used together, but neither are mandatory.

  查看最佳答案

• Which of the following commands should be used to assure that a dump can be forced using the reset button on a system without a key switch? （）

  A .  sysdumpdev -k  B .  sysdumpdev -L  C .  sysdumpdev -K  D .  sysdumpdev -P

  查看最佳答案

• Which command shows if an access list is assigned to an interface?（）

  A . show ip interface [interface] access-lists B . show ip access-lists interface [interface] C . show ip interface [interface] D . show ip access-lists [interface]

  查看最佳答案

• After executing the "show host" command, which of the information below would you see?（）

  A . The IP addresses of workstations allowed gain access to the router via an access list B . Permanent name-to-address mappings created using the ip host command. C . Temporary and permanent DNS entries. D . The names of the routers created using the hostname command. E . The length of time of users logged into the router, as well as the duratio

  查看最佳答案

• Which command will show the network configuration settings associated with an Ethernet adapter？（）

  A . lscfg B . lsdev C . netstat D . ifconfig

  查看最佳答案

• The sysdumpdev command can be used to configure remote dump devices. Which of the following conditions is NOT used for a remote dump device configuration?（）

  A . The local and the remote host must have Transmission Control Protocol/Internet Protocol (TCP/IP) installed and configured.  B . The remote host must support NFS.  C . The remote host must have an NFS exported directory defined such that the local host has read and write permissions to the dump file on the remote host.  D . The remote host can be the same as the local host.

  查看最佳答案

• Which command shows all the paging spaces available on a system?（）

  A . lsps -a B . showps -a C . psdisplay -l D . swaplist -ALL

  查看最佳答案

• Which command shows all the paging spaces available on a system？（）  

  A . lsps -a B . showps -a C . psdisplay -l D . swaplist -ALL

  查看最佳答案

• Which command shows if an access list is assigned to an interface？（）

  A . show ip interface [interface] access-lists B . show ip access-lists interface [interface] C . show ip interface [interface] D . show ip access-lists [interface]

  查看最佳答案

• Which command will show the MAC addresses of stations connected to switch ports?（）

  A . show mac-address B . show arp C . show table D . show switchport

  查看最佳答案

• Which of the following commands should be used to show DNS information？（）

  A .  trace B .  netstat C .  ifconfig D .  nslooku

  查看最佳答案

• Which command shows your active Telnet connections?（）

  A . show session B . show cdp neighbors C . show users D . show queue

  查看最佳答案

• Which IOS command shows the detailed error report?（）

  A . errpt -A  B . errpt -a  C . errlog -a  D . errlog -l

  查看最佳答案