-
Refer to the exhibit. Which statement is true about the 6.6.6.0/24 prefix?（）https://assets.asklib.com/images/image2/2018073013560246594.jpg
A . The command neighbor send -community is configured on BGP neighbor 10.10.23.3.
B . If another path advertises the 6.6.6.0/24 path and has the default local preference, that path is more preferred.
C . Route 6.6.6.0/24 is learned by an IBGP peer.
D . The route 10.10.23.3 is not being advertised to other BGP neighbors.
-
Refer to the exhibit. LACP has been configured on Switch1 as shown.
Which is the correct command set to configure LACP on Switch2？（）
https://assets.asklib.com/images/image2/2018073109354514482.jpg
A . Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode auto
B . Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode passive
C . Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode desirable
D . Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode o
-
Refer to the exhibit.If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?（）https://assets.asklib.com/images/image2/2018072411242431760.jpg
A . 192.168.1.1
B . 172.16.1.1
C . 1.1.1.1
D . 2.2.2.2
-
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?（）https://assets.asklib.com/images/image2/2018072410123247953.jpg
A . The path of the packets will be R3 to R2 to R1.
B . The path of the packets will be R3 to R1 to R2.
C . The path of the packets will be both R3 to R2 to R1 and R3 to R1.
D . The path of the packets will be R3 to R1
-
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?（）https://assets.asklib.com/images/image2/201807301607361324.jpg
A . The last default - network statement will always be preferred.
B . A route to the 140.140.0.0 network does not exist in the routing table.
C . Default - network selection will always prefer the statement with the lowest IP address.
D . A router will load balance across multiple default - networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.
-
Refer to the exhibit. Given the CPE deployment model, the Enterprise applications shown, and the functions being provided as designated, the appropriate product choice is _____.（）https://assets.asklib.com/images/image2/2018080114160985309.jpg
A . Cisco PIX 501 Firewall
B . Cisco 831 router
C . Cisco 837 router
D . Cisco VPN3002 Hardware Client
E . Cisco SW VPN Client
-
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown？（）https://assets.asklib.com/images/image2/201807241342138434.jpg
A . The Seria l0/0interface is passing traffic.
B . The DLCI 100 was dynamic allyallocated by the router
C . The Seria l0/0 interf aceacquired the IP address of 172.16.3.1 from a DHCP server
D . The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud
E . The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
-
Refer to the exhibit. An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?（）https://assets.asklib.com/images/image2/2018072409560147847.jpg
A . data link layer
B . application layer
C . access layer
D . session layer
E . network layer
-
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? （）https://assets.asklib.com/images/image2/2018073015150790983.jpg
A . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2
B . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1
C . R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1
D . R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
E . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
-
Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?（）https://assets.asklib.com/images/image2/2018073016391441987.jpg
A . router rip
B . router eigrp 10
C . redistribute eigrp 10
D . redistribute rip
E . default - metric 10000 100 255 1 1500
F . default - metric 5
-
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? （）https://assets.asklib.com/images/image2/2018073109011650113.png
A . area 0 stub o n routers R4 and R5
B . area 5 stub on routers R4 and R5
C . area 5 stub no - summary on routers R4 and R5
D . area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E . area 5 stub no - summary on router R4 and area 5 stub on router R5
-
Refer to the exhibit. The network has been configured with H.323 gateways and gatekeepers as shown. Which statement is true when a call is placed？（）https://assets.asklib.com/images/image2/2018072416330097077.jpg
A . A gatekeeper is contacted to determine the correct local gateway to use.
B . A gateway will receive the call and forward a call request to the local gatekeeper.
C . A gateway will receive the call and forward a call request to the gatekeeper on the other side of the WAN
D . A gatekeeper will receive the call and forward a call request to the remote gateway.
-
Refer to the exhibit. Given the CPE deployment model, the Enterprise applications shown, and the functions being provided as designated, the appropriate product choice is ____.（）https://assets.asklib.com/images/image2/2018080114383145557.jpg
A . Cisco PIX 501 Firewall
B . Cisco 831 router
C . Cisco 837 router
D . Cisco VPN3002 Hardware Client
E . Cisco ubr925 cable modem
F . Cisco SW VPN Client
-
Refer to the exhibit.
https://assets.asklib.com/images/image2/201807301615135089.png
Which order correctly identifies the steps to provision a cable modem to connect to a headend as defined by the DOCSIS standard？（）
A . A→D→C→G→E→F→B
B . A→D→E→G→C→F→B
C . C→D→F→G→E→A→B
D . C→D→F→G→A→E→B
E . F→D→C→G→A→E→B
-
Refer to the exhibit. What is the configuration an example of？（）
A . enabling modular QoS over Frame Relay
B . enabling Real-Time Transport Protocol （RTP） header compression
C . enabling distributed compressed Transmission Control Protocol
D . enabling latency and jitter reduction for Transmission Control traffic
E . enabling TCP header compressio
-
Refer to the exhibit. Which statement is true about the 6.6.6.0/24 prefix？（）https://assets.asklib.com/images/image2/2018072609483826162.jpg
A . If another path advertises the 6.6.6.0/24 path and has the default local preference， that path is more preferred
B . The command neighbor send-community is configured on BGP neighbor 10.10.23.3
C . The route 10.10.23.3 is not being advertised to other BGP neighbors
D . Route 6.6.6.0/24 is learned by an IBGP peer
-
Refer to the exhibit. By default, when RTB passes BGP advertisements from RTA about network 192.168.2.0 to RTC, what address will be listed as the next - hop address? （）https://assets.asklib.com/images/image2/2018073013521744638.jpg
A . 10.1.1.2
B . 192.168.1.49
C . 10.1.1.1
D . 192.168.1.50
-
Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1？（）https://assets.asklib.com/images/image2/2018073011483760789.jpg
A . Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAs
B . No redistributed routes can appear in Area 1, only summary routes
C . Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs
D . Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSA
-
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
https://assets.asklib.com/images/image2/2018073109302428070.jpg
A . All ports will be in forwarding mode.
B . All ports in VLAN 10 will be in forwarding mode.
C . All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D . All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
-
Refer to the exhibit. Given the CPE deployment model, the Enterprise applications shown, and the functions being provided as designated, the appropriate product choice is（）.https://assets.asklib.com/images/image2/2018080114072578756.jpg
A . Cisco PIX 501 Firewall
B . Cisco 831 router
C . Cisco 837 router
D . Cisco VPN3002 Hardware Client
E . Cisco ubr925 cable modem
F . Cisco SW VPN Client
-
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）https://assets.asklib.com/images/image2/2018073010540810068.jpg
A . Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.
B . Router R1 will advertise both rou tes.
C . Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.
D . Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
-
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area？ （）
<img src='https://img2.soutiyun.com/shangxueba/ask/64290001-64293000/64291910/529008d927b67f31920b5858e5879e0b.png' />
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
-
Refer to the exhibit. Which st atement is true？（）
<img src='https://img2.soutiyun.com/shangxueba/ask/64308001-64311000/64308470/76e6facffcf5f1271b76bfe3c5a96843.jpg' />
A. Router RTA is the BDR
B. Router RTA is directly connected to interface 192.168.45.1
C. Neighbor 192.168.45.1 has changed its OSPF priority number
D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
-
Refer to the exhibit. Which Virtual Router Redundancy Protocol （）
A．RouterAisthemastervirtualrouter，andRouterBisthebackupvirtualrouter．WhenRouterAfails，RouterBwillbecomethemastervirtualrouter．WhenRouterArecovers，RouterBwillmaintaintheroleofmastervirtualrouter．
B．RouterAisthemastervirtualrouter，andRouterBisthebackupvirtualrouter．WhenRouterAfails，RouterBwillbecomethemastervirtualrouter．WhenRouterArecovers，itwillregainthemastervirtualrouterrol
E．
C．RouterBisthemastervirtualrouter，andRouterAisthebackupvirtualrouter．WhenRouterBfails，RouterAwillbecomethemastervirtualrouter．WhenRouterBrecovers，RouterAwillmaintaintheroleofmastervirtualrouter．
D．RouterBisthemastervirtualrouter，andRouterAisthebackupvirtualrouter．WhenRouterBfails，RouterAwillbecomethemastervirtualrouter．WhenRouterBrecovers，itwillregainthemastervirtualrouterrol
E．
