-
Refer to the exhibit. Which [ephone-dn type] would you expect to see in the partial show run output?（）https://assets.asklib.com/images/image2/2018080111321046423.jpg
A . shared
B . overlaid
C . dual-line
D . dual-label
E . single-line
F . dual-number
-
Refer to the exhibit.Explain how the routes in the table are being affected by the status change on interfaceEthernet0.（）https://assets.asklib.com/images/image2/2018072314074072169.jpg
A . The router is poisoning the routes and multicasting the new path costs via interface Ethernet1
B . The router is receiving updates about unreachable networks from router that are connected to interface Ethernet1
C . The router is poisoning the routes and broadcasting the new path costs via interface Ethernet1
D . The router is requesting updates for these networks from routers that are connected to interface Etherne1
-
Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? （）https://assets.asklib.com/images/image2/2018073114120422979.jpg
A . CEF switching is not needed for MPLS operation.
B . CEF switching is only needed to forward labeled packets.
C . CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled.
D . Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process.
E . Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.
-
Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? （）https://assets.asklib.com/images/image2/2018072409503135369.jpg
A . Configure the gateway on Host A as 10.1.1.1.
B . Configure the gateway on Host B as 10.1.2.254.
C . Configure the IP address of Host A as 10.1.2.2.
D . Configure the IP address of Host B as 10.1.2.2.
E . Configure the masks on both hosts to be 255.255.255.224.
F . Configure the masks on both hosts to be 255.255.255.240.
-
Refer to the exhibit.
https://assets.asklib.com/images/image2/2018073015594315172.png
What does the "26" in the first two hop outputs indicate？（）
A . the outer label used to determine the next hop
B . the IPv4 label for the destination network
C . the IPv4 label for the forwarding router
D . the IPv4 label for the destination router
-
Refer to the exhibit. On the basis of the information in the exhibit，which two statements are true？（）https://assets.asklib.com/images/image2/201807241128503880.jpg
A . Any traffic matching signature 1107 will generate an alarm， reset the connection，and be dropped.
B . Signature 1102 has been modified， but the changes have not been applied to the router.
C . Signature 1102 has been triggered because of matching traffic.
D . The Edit IPS window is currently displaying the Global Settings information.
E . The Edit IPS window is currently displaying the signatures in Details view.
F . The Edit IPS window is currently displaying the signatures in Summary view.
-
Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of procedures are best practices for Layer 2 and 3 failover alignment?（）https://assets.asklib.com/images/image2/2018072410174774893.jpg
A . Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B . Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
C . Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D . Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E . Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
F . Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12a nd 120. Configure the D-SW2 switch as the standby HSRP router and the backup STP root for VLANs 11 and 110.
-
Refer to the exhibit. In the diagram， the switches are running IEEE 802.1s MST. Which ports are in the MST blocking state？（）https://assets.asklib.com/images/image2/2018072317300046507.jpg
A . GE-1/2 and GE 2/1
B . GE-1/1 and GE-2/2
C . GE-3/2 and GE 4/1
D . no ports are in the blocking state
E . There is not enough information to determine which ports are in the blocking state.
-
Refer to the exhibit. On the basis of the information in the exhibit， which two statements are true？（）
A . When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2
B . The serial 0/0/1 interface on the ISP router has been configured with the set metric 50command
C . The output was generated by entering the show ip bgp command on the SanJose1 router
D . The output was generated by entering the show ip bgp command on the ISP router
E . The serial 0/0/1 interface on the ISP router has been configured with the set metric 75command
F . When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
-
Refer to the exhibit. What does the option secret 5 in the username global configuration mode commandindicate about the enable secret password？（）
A . It is hashed using SHA
B . It is encrypted using DH group 5
C . It is hashed using MD5
D . It is encrypted via the service password-encryption command
E . It is hashed using a proprietary Cisco hashing algorithm
F . It is encrypted using a proprietary Cisco encryption algorithm
-
Refer to the exhibit.
Which protocol establishes an optimal path to the root in a wireless mesh network？ （）
https://assets.asklib.com/images/image2/2018073011454335678.jpg
A . Adaptive Wireless Path （AWP）
B . WLAN Quality of Service （WQoS）
C . Lightweight Access Point Protocol （LWAPP）
D . 802.1Q WLAN trunking protocol
E . Layer 2 Roaming （IAPP）
-
Refer to the exhibit. In the diagram, the switches are running IEEE 802.1s MST. Which ports are in the MST blocking state?（）https://assets.asklib.com/images/image2/2018072317220752705.jpg
A . GE-1/2 and GE 2/1
B . GE-1/1 and GE-2/2
C . GE-3/2 and GE 4/1
D . no ports are in the blocking state
E . There is not enough information to determine which ports are in the blocking state
-
Refer to the exhibit. Which three statements are true about trust boundaries in the campus network？ （Choose three.）（）https://assets.asklib.com/images/image2/2018072411062788011.jpg
A . A device is trusted if it correctly classifies packets.
B . A device is trusted if it correctly declassifies packets.
C . The outermost trusted devices represent the trust boundary.
D . Classification and marking occur using 802.1ab QoS bits before reaching the trust boundary.
E . Network trust boundaries are automatically configured in IOS version 12.3 and later.
F . For scalability， classification should be done as close to the edge as possible.
-
Refer to the exhibit.How many broadcast domains exist in theexhibited topology？（）https://assets.asklib.com/images/image2/2018072414031738897.jpg
A . one
B . two
C . three
D . four
E . five
F . six
-
Refer to the exhibit. What does the (*) represent in the output?（）https://assets.asklib.com/images/image2/2018072310402175939.jpg
A . Packet is destined for a local interface to the router.
B . Packet was translated, but no response was received from the distant device.
C . Packet was not translated, because no additional ports are available.
D . Packet was translated and fast switched to the destination.
-
Refer to the exhibit. Based upon the information in the exhibit， which statement is true？（）https://assets.asklib.com/images/image2/2018072614035912006.jpg
A . DHCP requests from the host will be rebroadcasted to R2
B . To complete this configuration， the R1 fa0/0 interface must be configured with the ip helper-addresses command
C . To complete this configuration， the R2 fa0/0 interface must be configured with the ip helper-addresses command
D . R1 will forward all DHCP requests to both 192.168.100.1 and 192.168.200.1 as unicastmessages
E . R1 will forward DHCP requests to 192.168.100.1. If there is no response， R1 will then forwardthe requests to 192.168.200.1
-
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause？（）
https://assets.asklib.com/images/image2/2018073011222764982.jpg
A . IP routing is not enabled.
B . VTP is not configured correctly on the interfaces.
C . The command mls rp management-interface is missing.
D . The command mls rp ip must be disabled to enable the routing.
-
Refer to the exhibit. A display of class maps for a configuration is shown in the exhibit. What will the class-map "all-traffic" match? （）https://assets.asklib.com/images/image2/2018073114131723118.jpg
A . all voice traffic
B . all traffic with dscp 18 or dscp 43
C . all traffic with dscp 18 and dscp 43
D . all traffic with ip precedence 0 or 1
E . all traffic with ip precedence 4 and 5
-
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?（）https://assets.asklib.com/images/image2/2018073015260438802.jpg
A . DHCP requests from the host will be rebroadcasted to R2.
B . To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.
C . To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.
D . R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.
E . R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
-
Refer to the exhibit.
https://assets.asklib.com/images/image2/2018072411074671886.jpg
According to the equipment tab in Cisco UCS Manager， which is true？（）
A . A is an uplink port， B is a fabric port， C is a server port， D is a backplane port， E is a DCE interface， and F is a vNIC
B . A is an uplink port， B is a server port， C is a fabric port， D is a backplane port， E is a DCE interface， and F is a vNIC
C . A is an uplink port， B is a fabric port， C is a backplane port， D is a server port， E is a DCE interface， and F is a vNIC
D . A is an uplink port， B is a server port， C is a fabric port， D is a DCE interface， E is a backplane port， and F is a vNIC
E . A is an fabric port， B is a downlink port， C is an uplink port， D is a server port， E is a VIC interface， and F is a vNIC
-
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）https://assets.asklib.com/images/image2/2018073010540810068.jpg
A . Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.
B . Router R1 will advertise both rou tes.
C . Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.
D . Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
-
Refer to the exhibit.
Which three statements are true about trust boundaries in the campus network？（）
https://assets.asklib.com/images/image2/2018073014302987878.jpg
A . Classification and markingoccur using 802.1ab QoS bits before reaching the trust boundary.
B . A device is trusted if it correctly declassifies packets.
C . A device is trusted if it correctly classifies packets.
D . Network trust boundaries are automatically configured in IOS version 12.3 and later.
E . The outermost trusted devices represent the trust boundary.
F . For scalability， classification should be done as close to the edge as possible.
-
Refer to the exhibit. Easy VPN operates in two modes. The exhibit represents network extension mode. Choose the best reason for using this mode.（）https://assets.asklib.com/images/image2/2018080114285155907.jpg
A . Teleworker devices must be accessed from the central site (server, printers).
B . IP addressing is simplified.
C . The Teleworker LAN is a transit networking for routing.
D . The Teleworker router is an MPLS PE node.
-
Refer to the exhibit. What statement is true base d upon the configuration in the exhibit? （）https://assets.asklib.com/images/image2/2018073015050639705.jpg
A . CGMP version 2 is being used.
B . The switch will use sparse mode first, dense mode second.
C . A rendezvous point must be configured in order for the interface to operate in sparse mode.
D . IGMP version 2 is being used.
E . The rendezvous point is IP address 172.16.4.16.
F . If a rendezvous point is configured, the interface cannot operate in dense mode.
-
Refer to the exhibit. How many broadcast domains exist in the exhibited topology?dc7fe144cddd7e03e1f5f5398da13a2f.jpg
