When configuring private VLANs， which configuration task must you do first？（）

相似题目

• When configuring cisco secure acs to support wireless eap authentication，which device must be configured as a aaa client？（）

  A . location appliance B . controller-based access points C . wireless clients D . wireless control system E . wireless controller

  查看最佳答案

• Which of these is mandatory when configuring Cisco IOS Firewall？ （）

  A . Cisco IOS IPS enabled on the untrusted interface B . NBAR enabled to perform protocol discovery and deep packet inspection C . a route map to define the trusted outgoing traffic D . a route map to define the application inspection rules E . an inbound extended ACL applied to the untrusted interface

  查看最佳答案

• When implementing OSPFv3, which statement describes the configuration of OSPF areas?（）

  A . In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas. B . In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas. C . In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas. D . In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.

  查看最佳答案

• When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）

  A . The local DLCI on each subinterface of the Frame Relay. B . The Frame Relay encapsulation on the physical interface. C . An IP address on the physical interface. D . The subinterface type as point-to-point

  查看最佳答案

• What OSPF command, when configured, will include all interfaces into area 0?（）

  A . network 0.0.0.0 255.255.255.255 area 0 B . network 0.0.0.0 0.0.0.0 area 0 C . network 255.255.255.255 0.0.0.0 area 0 D . network all-interfaces area 0

  查看最佳答案

• How is NIC teaming configured when port channels are not in use in a Cisco Nexus 1000V?（）

  A . active / active using spanning tree B . active / active C . active / passive using spanning tree D . active / passive

  查看最佳答案

• Switch R1 has been configured with Private VLANs.  With that type of PVLAN port should the default gateway be configured？（）

  A .  Trunk B .  Isolated C .  Primary D .  Community E .  Promiscuous F .  None of the other alternatives apply

  查看最佳答案

• When configuring Cisco IOS login enhancements for virtual connections， what is the "quiet period"？（）

  A . The period of time in which virtual login attempts are blocked， following repeated failed login attempts B . The period of time in which virtual logins are blocked as security services fully initialize C . A period of time when no one is attempting tolog in D . The period of time between successive login attempt

  查看最佳答案

• When configuring a serial interface on a router, what is the default encapsulation?（）

  A . atm-dxi B . frame-relay C . hdlc D . lapb E .

  查看最佳答案

• How many VLANs on the UCS must be configured when using FCoE?（）

  A . One per blade B . One per VSAN C . One per fabric D . None are required

  查看最佳答案

• Private VLANS can be configured as which three of these port types？（）

  A . isolated B . protected C . private D . associated E . promiscuous F . munity

  查看最佳答案

• Cisco Configuration Assistant supports a variety of virtual private networks. Which three types of VPN can be configured by using CCA？（）

  A .  DMVPN B .  MPLS VPN C .  IPv6 VPN D .  Cisco IOS SSL VPN E .  site-to-site VPN F .  Cisco Easy VPN

  查看最佳答案

• When a Cisco router is configured for SSH, it acts as an （）?

  A . SSH client B . SSH proxy C . SSH server D . SSH and SSL server

  查看最佳答案

• When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）

  A . Wireless Control System B . wireless clients C . wireless controllers D . controller-based access points E . Location Appliance

  查看最佳答案

• What should you set the Client Configuration to when configuring the ODBC Data Source for the Database Subsystem?（）

  A . TCP/IP   B . Multiprotocol   C . Named Pipes   D . NWLink IPX/SPX

  查看最佳答案

• Which two statements correctly identify factors to consider when Configuring WAN QoS？（）

  A . Voice Traffic uses Assured Forwarding B . Voice Signaling traffic uses Assured Forwarding C . Voice Signaling traffic uses priority queuing D . Voice Traffic uses priority queuing E . Voice signaling traffic should use priority queuing with Assured Forwarding

  查看最佳答案

• Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）

  A . Trunk B . Isolated C . Primary D . Community E . Promiscuous F . None of the other alternatives apply

  查看最佳答案

• When configuring system state conditions with the Cisco SecurityAgent， what is the resulting action when configuring more than one system state condition？ （）

  A . Any matching state condition will result with the state being triggered B .  Once a state condition ismet， the system ceases searching further conditions and will cause the state condition to trigger C .  All specified state conditions are used as part of the requirements tobe met to for the state to trigger D .  Once the state conditions are met， they become persistent and can only be removed using the Reset feature

  查看最佳答案

• When configuring SSH， which is the Cisco minimum recommended modulus value？（）

  A . 2048 bits B . 1024 bits C . 256 bits D . 512 bit

  查看最佳答案

• Your portable computer has a Virtual Private Network （VPN） connection configured. You need to connect to the VPN.  What should you do？（）

  A . Use the Mobile PC program. B . Use the Ease of Access program. C . Use the System and Maintenance program. D . Use the Network and Sharing Center program.

  查看最佳答案

• When will an "all configuration" backup be imported into the Cisco UCS Manager？（）

  A .  During the initial configuration from the console B .  Once the basic configuration has been applied C .  To restore the configuration on a secondary fabric interconnect D .  To upgrade the firmware on a replacement fabric interconnect

  查看最佳答案

• When configuring unified ports on a 5548 switch， which port ordering must be respected？（）

  A .  Fibre Channel ports must be configured from the first port in the module. B .  Ethernet ports must be configured from the last port in the module. C .  Fibre Channel ports must be configured from the last port in the module. D .  Ethernet ports must be configured from the first port in the module.

  查看最佳答案

• Which does not need to be configured on ZXCTN6100 when performing basic configuration

  A．A.UNI interface configuratio B．B.Static MAC configuratio C．C.configuratio D．D.VLAN interface configuratio

  查看最佳答案

• When a guest calls to reserve a private room for dinner, what information doyou have to know？

  查看最佳答案