N1 IF R2 〉10 GOTOB MARKE3;中“〉”表示大于。(SIEMENS系统)()
相似题目
-
If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1, which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner (R2) and become a trunk? ()
-
串联电路R1=8Ω,R2=10Ω,总电压U=36V,则R2两端的电压是()V。
-
已知R1=5Ω,R2=10Ω,把R1、R2串联后接入220V电源,R1上的分压应为()。
-
两个电阻并联的电路,R1=10欧姆,R2=5欧姆,总电流为3A.则分配到R2接上的电流I2=()
-
已知R1=5、R2=10,把R1和R2串联后接入220伏电源,R1上的分压应为()。
-
Two directly connected routers, R1 and R2, are both configured for OSPF graceful restart. R2 is able to switch packets in hardware, but R1 is not. If a network administrator logs on to R2 and performs a system reload, which will be the result?()
-
如果两样本r1=r2,n1>n2,那么()
-
If you were to configure an ISL Ethernet trunk between two Cisco switches, named R1 and R2, what would you have to include at the end of the link for the trunk to operate correctly? ()
-
已知R1=10,R2=10,把两个电阻并联起来,其总电阻为()。
-
如果两样本r1=r2,n1>n2,那么()。
-
有以下语句段 int n1=10,n2=20; printf(______ ,n1,n2); 要求按以下格式输出n1和n2的值,每个输出行从第一列开始,请填空。 n1=10 n2=20
-
R1与R2并联后接到10V电源上,电源的输出功率为25W,若R1=4R2,则R2为
-
S1、S2是两个相干光源,它们到P点的距离分别为r1和r2.路径S1P垂直穿过一块厚度为d1,折射率为n1的介质板,路径S2P垂直穿过厚度为d2,折射率为n2的另一介质板,其余部分可看作真空,这两条路径的光程差等于
-
已知语句n1, n2 = n2, n1的作用是将n1和n2的值互换位置,则如下程序段的功能是什么? if n1 >n2: n1, n2 = n2, n1if n2 >n3: n2, n3 = n3, n2if n1 >n2: n1, n2 = n2, n1
-
IF R1 〉= R2 GOTOF LABEL1 …LABEL1:…是()
-
“IF R1>=R2 GOTOFLABEL…LABEL:…;”是()(SIEMENS系统)
-
运行下方代码段,输出的是()。n1, n2 = 3, 4if n1 < n2:n1, n2 = n2, n1print(n1, n2)
-
IF R2=10…中”R2= 10表示()
-
N1IF[2GT10]中GT表示大于(FANUC系统\华中系统)()
-
下面程序的运行结果是()。includedefineN3intfun(intv[],intn,int*v1)voidmain(){inta[N][N]={1,2,3,4,5,6,7,8,9}intn1,n2n1=fun(*a,N,&n2)printf("n1=%d,n2=%d/n",n1,n2)}intfun(intv[],intn,int*v1){inti,j,nvnv=*v1=0for(i=0ifor(j=0j{if(i==j)nv+=v[i*n+j]if(i+j==n-1)*v1+=v[i*n+j]}returnnv}
-
图示电路中,已知R1=10Ω,R2=2Ω,Us1 =10V,Us2 = 6V。电阻R2两端的电压 U为()
-
两个阻值分别为R1=10Ω,R2=5Ω的电阻串联。由于R2电阻小,对电流的阻碍作用小,故流过R2的电流比R1中的电流大些。()
-
已知语句n1, n2 = n2, n1的作用是将n1和n2的值互换位置,则如下程序段的功能是什么? if n1 > n2: n1, n2 = n2, n1 if n2 > n3: n2, n3 = n3, n2 if n1 > n2: n1, n2 = n2, n1()
-
有以下语句段int n1=10,n2=20;printf();要求按以下格式输出n1和n2的值,每个输出行从第一列开始,请填空。n1=10n2=20