-
Which path is required to be present within a WAR file？（）
A . /classes
B . /index.html
C . /MANIFEST-INF
D . /WEB-INF/web.xml
E . /WEB-INF/classes
F . /WEB-INF/index.html
G . /META-INF/index.xml
-
Spanning Tree Protocol calculates path cost based on which of these？ （）
A . interface bandwidth
B . interface delay
C . interface bandwidth and delay
D . hop count
E . bridge priority
-
Which router or router combination is used to calculate the MPLS traffic engineering tunnel path？（）
A . head-end router and tail-end router
B . middle-point router
C . head-end router
D . tart-end router
E . tail-end router
-
panning Tree Protocol calculates path cost based on which of these？（）
A . interface bandwidth
B . interface delay
C . interface bandwidth and delay
D . hop count
E . bridge priority
-
Which path selection protocol is used by Fibre Channel fabrics？（）
A . IVR
B . VoQ
C . FSPF
D . VSANs
E . SANTa
-
Which of the following choices correctly describes the difference between a data load via the conventional path and the direct path?（）
A . One runs faster than the other
B . A conventional path data load bypasses most of the Oracle RDBMS, whereas a direct path load is a high-speed version of the SQL INSERT
C . A direct path data load bypasses most of the Oracle RDBMS, whereas a conventional path load is a high-speed version of the SQL INSERT
D . The conventional path runs when the CONVENTIONAL command-line parameter is set to TRUE
-
Which two are true regarding direct-path exports？（）
A . Direct-path export is typically faster.
B . Direct-path export can be invoked interactively.
C . Direct-path export is character set independent.
D . Direct-path export bypasses the SQL-command processing layer.
E . Direct-path export can be used to export rows containing LOBs and BFILEs.
-
Which two statements about spanning tree path cost are true？（）
A . The path cost can be changed for an interface using the spanning-tree cost command
B . The path cost can be changed for an interface using the stp path-cost command
C . The SPT default path cost depends on the interface speed
D . The STP default path cost is similar for all interface
-
Which three Cisco CRS upgrade paths are supported? （）
A . Cisco CRS 2.2 to Cisco CRS 3.5
B . Cisco CRS 2.2 to Cisco CRS 4.0
C . Cisco CRS 3.1 to Cisco CRS 4.0
D . Cisco CRS 3.5 to Cisco CRS 4.0
E . Cisco CRS 4.0 to Cisco CRS 3.0
F . Cisco CRS 4.0 to Cisco CRS 4.5
-
BGP best route selection process is based on path attributes.（）
A . True
B . False
-
How can the administrator display the boot paths from which AIX can boot？（）
A . bootinfo -r
B . lspath -boot
C . bosboot -ad hdisk0
D . bootlist -m normal -rv
-
Which one of the following files includes the parameter NAMES.DIRECTORY_PATH（hostname）？（）
A . Listener.ora
B . Tnsnames.ora
C . Cman.ora
D . Sqlnet.ora
-
By default, which of the following factors determines the spanning-tree path cost?（）
A . It is the individual link cost based on latency
B . It is the sum of the costs based on bandwidth
C . It is the total hop count
D . It is dynamically determined based on load
-
Which path is required to be present within a WAR file？（）
A . /classes
B . /index.html
C . /MANIFEST-INF
D . /WEB-INF/web.xml
E . /WEB-INF/classe
-
Which command records the path taken by network packets between a source and destination system? （）
A . traceroute
B . netstat -p
C . ping
D . netstat -r
-
Which statement is true about loading data using the conventional path of SQL*Loader（）
A . Redo is not generated while performing conventional path loads.
B . Only PRIMARY KEY， UNIQUE KEY， and NOT NULL constraints are checked.
C . No exclusive locks are acquired when the conventional path loads are performed.
D . Instead of performing transactions， SQL*Loader directly writes data blocks to the data files.
E . INSERT triggers are disabled before the conventional path load and reenabled at the end of the load
-
At which OSI layer is a logical path created between two host systems（）。
A . session
B . transport
C . network
D . data link
E . physical
-
Which command can be a router to verify the layer 3 path to a host?（）
A . traceroute address
B . tracert address
C . ssh address
D . telnet addre
-
Which BGP path attribute is Cisco proprietary?（）
A . weight
B . MED
C . local preference
D . origin
E . next - hop
F . AS - path
-
How can the administrator display the boot paths from which AIX can boot?（）
A . bootinfo -r
B . lspath -boot
C . bosboot -ad hdisk0
D . bootlist -m normal -rv
-
Unicast Reverse Path Forwarding can perform all of these actions except which one？（）
A . examine all packets received to make sure that the source addresses and source interfaces appear in the routing table and match the interfaces where the packets were received
B . check to see if any packet received at a router interface arrives on the best return path
C . combine with a configured ACL
D . log its events，if you specify the logging options for the ACL entries used by the unicast rpf command
E . inspect IP packets encapsulated in tunnels， such as GRE
-
At which OSI layer is a logical path created between two host systems?（）
A . session
B . transport
C . network
D . data link
E . physical
-
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values.Which statement is true about how BGP would select the best path？（）
A. To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
B. Th e router will prefer the shortest autonomous system path
C. If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
D. The router will prefer the route with the lower MED
-
About 1+1 T-MPLS path protection structure, which of the following are correct?
A.nIn 1+1 T-MPLS path protection structure, each working connection has a specific protection connection; working connection and protection connection are bridged at source end of protecting domain.
B.nIn 1+1 T-MPLS path protection structure, if a unidirectional fault (transmission direction from node A to Z) occurs to working connection, it will be detected at sink node Z of protecting domain and then node Z selector will switch to protection connectio
C.n1+1 T-MPLS path protection is of unidirectional switching type -- that is to say, only the affected end needs to switch to the protection path and selectors at the two ends are relatively independent.
D.nIn 1+1 T-MPLS path protection structure, to avoid single-point fault, working connection and protection connection should run along isolated routes.
此题为多项选择题。
