-
Refer to the exhibit. What is the meaning of the output MTU 1500 bytes?()https://assets.asklib.com/images/image2/2018072317543588105.jpg
A . Themaximumnumberofbytesthatcantraversethisinterfacepersecondis1500.
B . Theminimumsegmentsizethatcantraversethisinterfaceis1500bytes.
C . Theminimumpacketsizethatcantraversethisinterfaceis1500bytes.
D . Themaximumpacketsizethatcantraversethisinterfaceis1500bytes.
E . Themaximumframesizethatcantraversethisinterfaceis1500bytes.
-
Refer to the exhibit.
What is the configuration an example of? ()
https://assets.asklib.com/images/image2/2018073015220049716.jpg
A . GLBP weighting
B . default AVF and AVG configuration
C . GLBP MD5 authentication
D . GLBP text authentication
E . GLBP timer manipulatio
-
Refer to the exhibit. Given the topology shown, what are two ways to allow the VPN to operate?()https://assets.asklib.com/images/image2/2018080114364950184.jpg
A . Use route maps on the 831
B . The 831 has IPSec NAT-Transparency (NAT-T) enabled
C . Disallow split tunneling on the 831
D . IPSec pass-through must be enabled on the Linksys
E . Use the port-mapping feature on the residential router
-
Refer to the exhibit.
https://assets.asklib.com/images/image2/2018073015594315172.png
What does the "26" in the first two hop outputs indicate?()
A . the outer label used to determine the next hop
B . the IPv4 label for the destination network
C . the IPv4 label for the forwarding router
D . the IPv4 label for the destination router
-
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?()https://assets.asklib.com/images/image2/2018073015315977122.jpg
A . Interface authentication must be configured
B . The routing processes must be configured with an area ID
C . IP unicast routing must be enabled
D . IPv4 ad dresses must be applied to the interface
-
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?()
A . HostA is not on the same subnet as its default gateway
B . The address of SwitchA is a subnet address
C . The Fa0/0 interface on RouterA is on a subnet that cannot be used
D . The serial interfaces of the routers are not on the same subnet
E . The Fa0/0 interface on RouterB is using a broadcast addre
-
Refer to the exhibit. What two statements are true?()https://assets.asklib.com/images/image2/2018072615071070209.jpg
A . The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808
B . This is the designated router (DR) on the FastEthernet 0/0 link
C . Interface FastEthernet 0/0 was configured with the ipv6 ospf 1 area 1 command
D . OSPF version 2 has been enabled to support IPv6
E . The output was generated by the show ip interface command
-
Refer to the exhibit. What two statements are true?()https://assets.asklib.com/images/image2/2018073014095357352.jpg
A . This is the designated router (DR) on the FastEthernet 0/0 link.
B . The output was generated by the show ip interface c ommand.
C . The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D . The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E . Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F . OSPF version 2 has been enabled to support IPv6.
-
Refer to the exhibit. What command sequence will enable PAT from the inside to outside network?()https://assets.asklib.com/images/image2/2018072310395019011.jpg
A . (config) ip nat pool isp-net 1.2.4.2 netmask 255.255.255.0 overload
B . (config-if) ip nat outside overload
C . (config) ip nat inside source list 1 interface ethernet1 overload
D . (config-if) ip nat inside overload
-
Refer to the exhibit. What does the option secret 5 in the username global configuration mode commandindicate about the enable secret password?()
A . It is hashed using SHA
B . It is encrypted using DH group 5
C . It is hashed using MD5
D . It is encrypted via the service password-encryption command
E . It is hashed using a proprietary Cisco hashing algorithm
F . It is encrypted using a proprietary Cisco encryption algorithm
-
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?()
A . There is a mismatch in encapsulation types
B . The wrong type of cable is connected to the interface
C . The interface has been configured with the shutdown command
D . The interface is not receiving any keepalives
E . The interface needs to be configured as a DTE device
F . There is no encapsulation type configured
-
Refer to the exhibit. What is the most appropriate summarization for these routes?()https://assets.asklib.com/images/image2/2018072410531258943.jpg
A . 10.0.0.0/21
B . 10.0.0.0/22
C . 10.0.0.0/23
D . 10.0.0.0/24
-
Refer to the exhibit.What is the effect of the configuration that is shown?()
A . It tells the router or switch to try establish an SSH connection first and if that fail to use telnet.
B . It configures a cisco network device to use the SSH protocol on incoming communications via the virtual terminal ports.
C . It allows seven failed login attempts before the VTY lines are temporarily shutdown.
D . It configures the virtual terminal lines with the password 030752180500.
E . It configures SSH globally for all logins.
-
Refer to the exhibit. What does the (*) represent in the output?()https://assets.asklib.com/images/image2/2018072310402175939.jpg
A . Packet is destined for a local interface to the router.
B . Packet was translated, but no response was received from the distant device.
C . Packet was not translated, because no additional ports are available.
D . Packet was translated and fast switched to the destination.
-
Refer to the exhibit. What is the configuration an example of?()
A . enabling modular QoS over Frame Relay
B . enabling Real-Time Transport Protocol (RTP) header compression
C . enabling distributed compressed Transmission Control Protocol
D . enabling latency and jitter reduction for Transmission Control traffic
E . enabling TCP header compressio
-
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.What is the cause of this failure?()
A . A level 5 password is not set
B . The vty password is missing
C . The console password is missing
D . An ACL is blocking Telnet acce
-
Refer to the exhibit.What is the result of setting the no login command?()https://assets.asklib.com/images/image2/2018072314480141170.jpg
A . The is a virtually limitless supply of IP addresses
B . Telnet access requires a new password at first login
C . Telnet access requires a password
D . Telnet access is denied
-
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? ()
A . Router1 has specific boot system command that instruct it to load IOS from TFTP server.
B . Router1 is acting as a TFTP server for other routers.
C . Router1 cannot locate a valid IOS image in flash memory.
D . Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
E . Cisco routers will first attempt to load a image from TFTP for management purposes.
-
Refer to the exhibit.
What is the problem with this configuration?()
https://assets.asklib.com/images/image2/201807301056416734.jpg
A . Spanning tree PortFast cannot be configured on a port where a voice VLAN is configured.
B . Sticky secure MAC addresses cannot be used on a port when a voice VLAN is configured.
C . Spanning tree PortFast cannot be configured on a port when a sticky secure MAC address is used.
D . The switch port must be configured as a trunk.
-
Refer to the exhibit. What statement is true base d upon the configuration in the exhibit? ()https://assets.asklib.com/images/image2/2018073015050639705.jpg
A . CGMP version 2 is being used.
B . The switch will use sparse mode first, dense mode second.
C . A rendezvous point must be configured in order for the interface to operate in sparse mode.
D . IGMP version 2 is being used.
E . The rendezvous point is IP address 172.16.4.16.
F . If a rendezvous point is configured, the interface cannot operate in dense mode.
-
Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
https://assets.asklib.com/images/image2/2018073109320145794.jpg
A . ip routing
B . no ip routing
C . router eigrp 1
D . no router eigrp 1
E . mls qos
F . no mls qo
-
Refer to the exhibit. On the basis of the output, what two conclusions can be reached?()
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/28e0d71a8ccd751c5a7f9c6a7dba7abf.jpg' />
A. The default administrative distance has been changed.
B. IS - IS is not enabled.
C. Three physical interfaces are taking part in integrated IS - IS.
D. IS - IS is not redistributing any oth er routing protocols.
E. There are two neighboring routers sending IS - IS routing information.
F. Address summarization is configured.
-
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? ()
<img src='https://img2.soutiyun.com/shangxueba/ask/64290001-64293000/64291910/529008d927b67f31920b5858e5879e0b.png' />
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
-
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?()
<img src='https://img2.soutiyun.com/ask/uploadfile/2019-03-27/67e52e69e1cc511a71a60a5d0c35c68a.jpg' />
A.The loopback addresses are on different subnets
B.The value of the dead timers on the router are different
C.Route summarization is enabled on both routers
D.The process indentifier on router A is different than the process identifier on router B