-
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch. How would you interconnect and configure LAG for connectivity and ensure redundancy？（）
A . All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channelgroup.
B . Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and CiscoWLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
C . All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
D . Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and CiscoWLC ports 3 and 4 to Catalyst gigabit module slot 2 channel group 40.
-
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）
A . switchport access vlan vlan-id
B . switchport
C . switchport mode access
D . no switchport
E . None of the other alternatives apply
-
What are two characteristics of a switch that is configured as a VTP client?（）
A . if a switch that is configured to operate in client mode cannot access a VTP server,then the switch reverts to transparent mode.
B . The local vlan configuration is updated only when an update that has a higher configuration revision number is received.
C . Vtp advertisements are not forwarded to neighboring switches that are configured in vtp transparent mode.
D . When switches in vtp client mode are rebooted,they send a vtp advertisement request to the vtp servers.
E . Vtp client is the default vtp mode
F . On switches that are configured to operate in client mode ,vlans can be created,deleted,or renamed locally
-
What are three of the functions that AutoQoS performs when it is configured on a switch？（）
A . synchronizes FIFO， PQ， CQ， and MDRR， with WFQ， CBWFQ， and LLQ
B . enables strict priority queuing for voice traffic， and weighted round robin queuing for data traffic
C . enables low latency queuing to ensure that voice traffic receives priority treatment
D . enforces a trust boundary on switch access ports and uplinks/downlinks
E . modifies queue sizes as well as queue weights where required
F . adjusts link speeds to adapt to QoS need
-
Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）
A . Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.
B . R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.
C . R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.
D . All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
-
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
A . RSTP information is automatically aged out.
B . The port sends a TCN to the root bridge.
C . The port moves to listening state.
D . The port becomes a normal spanning tree port.
-
A system administrator installed a new switch using a script to configure it. IP connectivity was tested using pings to SwitchB. Later attempts to access NewSwitch using Telnet from SwitchA failed. Which statement is true？（）
A . Executing password recovery is required.
B . The virtual terminal lines are misconfigured.
C . Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D . Power cycle of NewSwitch will return it to a default configuration.
-
A system administrator installed a new switch using a script to configure it. IP connectivity was tested using pings to SwitchB.Later attempts to access NewSwitch using Telnet from SwitchA faileD.Which statement is true?（）
A . Executing password recovery is required.
B . The virtual terminal lines are misconfigured.
C . Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D . Power cycle of NewSwitch will return it to a default configuration.
-
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? （）https://assets.asklib.com/images/image2/2018073015150790983.jpg
A . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2
B . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1
C . R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1
D . R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
E . S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
-
f a Cisco switch is configured with VTPv1 in transparent mode， what is done with received VTP advertisements？（）
A . They are discarded
B . The contents are altered to reflect the switch’s own VTP database and then they are forward out all trunking ports
C . The changes within the advertisements are made to the switch’s VTP database.
D . The contents are ignored and they are forwarded out all trunking ports.
-
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?（）
A . All defined VLANs are allowed on the trunk by default.
B . Each VLAN, or VLAN range, that is specified with the switchport mode command.
C . Each VLAN, or VLAN range, that is specified with the vtp domain command.
D . Each VLAN, or VLAN range, that is specified with the vlan database command.
-
Which of these best describes the actions taken when a VTP message is received on a switch configured with the VTP mode "transparent"？ （）
A . VTP updates are ignored and forwarded out all ports.
B . VTP updates are ignored and forwarded out trunks only.
C . VTP updates are made to the VLAN database and are forwarded out trunks only.
D . VTP updates are ignored and are not forwarded.
-
The following was configured on a switch： Switch（config） # spanning-tree portfast bpdufilter default What is the effect of this configuration command？（）
A . If BPDUs are received by a port configured for PortFast， they are ignored and none are sent.
B . The command will enable BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
C . If BPDUs are received by a port configured for Portfast， the port will transition to forwarding state.
D . If BPDUs are received by a port configured for PortFast， then PortFast is disabled and the BPDUs are processed normally.
E . None of the other alternatives apply.
-
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link?（）
A . no VLANs
B . all VLANs
C . only VLANs 1 - 64
D . only the VLANs that are specified when creating the trunk
-
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link（）。
A . no VLANs
B . all VLANs
C . only VLANs 1 - 64
D . only the VLANs that are specified when creating the trunk
-
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）
A . For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.
B . For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.
C . Direct inter-vlan communication does not require OSPF
D . OSPF cannot be used if router-on-a-stick is configured on the router
-
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct，
what will be true about Switch 15？（）
https://assets.asklib.com/images/image2/2018073109302428070.jpg
A . All ports will be in forwarding mode.
B . All ports in VLAN 10 will be in forwarding mode.
C . All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D . All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
-
ISL is being configured on a Company switch. Which of the following choices are true regarding the ISL protocol？ （）
A . It can be used between Cisco and non-Cisco switch devices.
B . It calculates a new CRC field on top of the existing CRC field.
C . It adds 4 bytes of protocol-specific information to the original Ethernet frame.
D . It adds 30 bytes of protocol-specific information to the original Ethernet frame.
-
When configuring port security on a Cisco Catalyst switch port， what is the default action taken by the switch if a violation occurs？ （）
A . protect （drop packets with unknown source addresses）
B . restrict （increment SecurityViolation counter）
C . shut down （access or trunk port）
D . transition （the access port to a trunking port）
-
A cisco 4404 wlan controller is being connected to a cisco 6500 catalyst series switch. How would you interconnect and configure lag for connectivity and ensure redundancy？（）
A . all four ports from the cisco wlc terminated to the same catalyst gigabit module and channel group.
B . ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 10 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 10.
C . all four ports from the cisco wlc terminated to the same catalyst gigabit module using two channel groups.
D . ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 20 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 40.
-
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch. How would younterconnect and configure LAG for connectivity and ensure redundancy？（）
A . All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channel group.
B . All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
C . Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 40.
D . Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
-
What are two characteristics of a switch that is configured as a VTP client？（）
A . if a switch that is configured to operate in client mode cannot access a VTP server，then the switch reverts to transparent mode.
B . The local vlan configuration is updated only when an update that has a higher configuration revision number is received.
C . Vtp advertisements are not forwarded to neighboring switches that are configured in vtp transparent mode.
D . When switches in vtp client mode are rebooted，they send a vtp advertisement request to the vtp servers.
E . Vtp client is the default vtp mode
F . On switches that are configured to operate in client mode ，vlans can be created，deleted，or renamed locally
-
Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?（）https://assets.asklib.com/images/image2/2018072316420345545.jpg
A . The number of collision domains would decrease.
B . The number of collision domains would increase.
C . The number of broadcast domains would remain the same.
D . The number of collision domains would remain the same.
E . The number of broadcast domains would increase.
-
When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）
A . Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B . Enter the no switchport command to disable Layer 2 functionality at the interface level.
C . Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D . Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
