Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）

相似题目

• You install a wireless router and disable the Service Set Identifier （SSID） broadcast feature. You need to configure your computer to connect to the wireless network.  What should you do？ （）

  A . Click the Connect to a network link， right-click the appropriate network， and then click the Connect option. B . Click the View computers and devices link， right-click the wireless router， and then click the Enable option. C . Click the Set up a connection or network link， and then click the Set up a wireless Ad hoc network option. D . Click the Set up a connection or network link， and then click the Manually connect to a wireless network option.

  查看最佳答案

• In a Teleworker deployment with a single IP phone connected to a Cisco 831 router, select the true statement regarding Call Admission Control.（）

  A . RSVP is a required configuration to support conference calls without voice packet loss.  B . The QoS configuration on the 831 router must always provision sufficient bandwidth for two RTP streams.  C . Call admission control is an issue only when using hardware DSP resources.  D . When using the conference call features on a 7960 IP phone, only one RTP stream is present regardless of how many extensions are on the conference.

  查看最佳答案

• For a router connected to two ISPs for redundancy， using IPSLA and static routing， how would youconfigure uRPF on the uplink interface？（）

  A . ip verify unicast source reachable-via any B . ip verify unicast reverse-path C . ip verify unicast reverse-path loose D . ip verify unicast reverse-path strict

  查看最佳答案

• This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）https://assets.asklib.com/images/image2/201807260848161736.png

  A . ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco B . Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco C . ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco D . Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco E . ACCESS1(config)# enable password cisco F . Remote27(config)# enable password cisco

  查看最佳答案

• When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the interface clock rate determined（）。

  A . It is supplied by the CSU/DSU. B . It is supplied by the far end router. C . It is determined by the clock rate command. D . It is supplied by the Layer 1 bit stream timing.

  查看最佳答案

• Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）

  A . Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload. B . R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed. C . R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state. D . All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.

  查看最佳答案

• Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?（）

  A . enable cdp B . cdp enable C . cdp run D . run cd

  查看最佳答案

• Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）

  A . R1 will always create and flood a default route into the OSPF domain. B . R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0. C . R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route. D . R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.

  查看最佳答案

• A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How canyou accomplish this task，using the fewest physical interfaces and withoutdecreasing networkperformance？（）

  A . Add two more FastEthernet interfaces. B . Add a second router to handle the vlan traffic. C . Use a hub to connect the four vlans with a FastEthernet interface on router. D . Implement a router-on-a-stick configuration.

  查看最佳答案

• You are preparing to create a point to point WAN by connecting a Cisco router with a Juniper router by way of their serial links. Which one of the following commands would you use?（）

  A . TK1(config-if)# encapsulation hdlc ansi B . TK1(config-if)# encapsulation ppp C . TK1(config-if)# encapsulation LAPD D . TK1(config-if)# encapsulation frame-relay ietf E . TK1(config)#encapsulation

  查看最佳答案

• For a router connected to two ISPs for redundancy， using IPSLA and static routing， how would you configure uRPF on the uplink interface？（）

  A . ip verify unicast source reachable-via any B . ip verify unicast reverse-path C . ip verify unicast reverse-path loose D . ip verify unicast reverse-path strict

  查看最佳答案

• Which command can be used on a PE router to connect to a CE router （11.1.1.4） in VRF red？（）

  A . telnet 11.1.1.4 /vrf-source red B . telnet 11.1.1.4 source /vrf red C . telnet 11.1.1.4 /source vrf red D . telnet 11.1.1.4 /vrf red E . telnet 11.1.1.4 vrf red

  查看最佳答案

• Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from  OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）

  A . Kilobits/seconD B . Tens of microseconds C . Cost D . Hop count E . No unit is assigneD

  查看最佳答案

• Which of the following IOS commands could you use to troubleshoot a router connectivity problem on an IP network?（）

  A . show ip route B . ipconfig C . tracert D . show interfaces E . traceroute F . ping G . All of the above

  查看最佳答案

• A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）

  A . For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration. B . For the two vlans to communicate， a network statement for each subinterface needs to be  added  to the OSPF configuration. C . Direct inter-vlan communication does not require OSPF D . OSPF cannot be used if router-on-a-stick is configured on the router

  查看最佳答案

• Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?（）

  A . ip ospf network broadcast B . ip ospf netw ork non - broadcast C . ip ospf network point - to - multipoint D . ip ospf network point - to - multipoint non - broadcast

  查看最佳答案

• A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How can you accomplish this task,using the fewest physical interfaces and without decreasing network performance?（）

  A . Add two more FastEthernet interfaces. B . Add a second router to handle the vlan traffic. C . Use a hub to connect the four vlans with a FastEthernet interface on router. D . Implement a router-on-a-stick configuration.

  查看最佳答案

• Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）

  A . TestKRouter(config-if)# Encapsulation frame-relay dot1q B . TestKRouter(config-if)# Encapsulation frame-relay aal5snap C . TestKRouter(config-if)# Encapsulation frame-relay ietf D . TestKRouter(config-if)# Encapsulation frame-relay isl E . None of the above

  查看最佳答案

• Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）https://assets.asklib.com/images/image2/2018073010540810068.jpg

  A . Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised. B . Router R1 will advertise both rou tes. C . Router R1 should be reconfigured with an ACL instead of an ip prefix - list command. D . Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.

  查看最佳答案

• A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? （）

  A . TE1 B . TE2 C . TA D . NT1 E . NT2

  查看最佳答案

• Area Border Router （ABR） is a router located on the border of one or more OSPF areas that connect those areas to the backbone network. An ABR will inject a default route into which two types of areas？（）

  A . Area 0 B . NSSA C . Totally stubby D . Stu

  查看最佳答案

• When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the interface clock rate determined?（）

  A . It is supplied by the CSU/DSU. B . It is supplied by the far end router. C . It is determined by the clock rate command. D . It is supplied by the Layer 1 bit stream timing.

  查看最佳答案

• Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.Which of the following is true about how IOS tries to limit EIGRP‘s use of bandwidth on S0/0？（）

  A.R1 limi ts EIGRP to around 250Kbps on DLCI 102 B.R1 limits EIGRP to around 250Kbps on DLCI 104 C.R1 limits EIGRP to around 150Kbps on every DLCI D.R1 does not limit EIGRP because noWAN bandwidth control has been configured

  查看最佳答案

• Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured？（）

  A. PPP on the ATM interface B. VPI/VCI on the dialer interface C. IP address on the ATM interface D. CHAP on the dialer interface

  查看最佳答案