Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?()
相似题目
-
You install a wireless router and disable the Service Set Identifier (SSID) broadcast feature. You need to configure your computer to connect to the wireless network. What should you do? ()
-
In a Teleworker deployment with a single IP phone connected to a Cisco 831 router, select the true statement regarding Call Admission Control.()
-
For a router connected to two ISPs for redundancy, using IPSLA and static routing, how would youconfigure uRPF on the uplink interface?()
-
This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? ()https://assets.asklib.com/images/image2/201807260848161736.png
-
When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the interface clock rate determined()。
-
Two directly connected routers, R1 and R2, are both configured for OSPF graceful restart. R2 is able to switch packets in hardware, but R1 is not. If a network administrator logs on to R2 and performs a system reload, which will be the result?()
-
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?()
-
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?()
-
A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How canyou accomplish this task,using the fewest physical interfaces and withoutdecreasing networkperformance?()
-
You are preparing to create a point to point WAN by connecting a Cisco router with a Juniper router by way of their serial links. Which one of the following commands would you use?()
-
For a router connected to two ISPs for redundancy, using IPSLA and static routing, how would you configure uRPF on the uplink interface?()
-
Which command can be used on a PE router to connect to a CE router (11.1.1.4) in VRF red?()
-
Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?()
-
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?()
-
Which of the following IOS commands could you use to troubleshoot a router connectivity problem on an IP network?()
-
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router,as the routing protocol for the network.Which statement about thisnetwork is true?()
-
A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How can you accomplish this task,using the fewest physical interfaces and without decreasing network performance?()
-
Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?()
-
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? ()https://assets.asklib.com/images/image2/2018073010540810068.jpg
-
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
-
Area Border Router (ABR) is a router located on the border of one or more OSPF areas that connect those areas to the backbone network. An ABR will inject a default route into which two types of areas?()
-
When a router is connected to a Frame Relay WAN link using a serial DTE interface, how is the interface clock rate determined?()
-
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.Which of the following is true about how IOS tries to limit EIGRP‘s use of bandwidth on S0/0?()
-
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()