Switch R1 is configured to use the VLAN Trunking Protocol (VTP). What does R1 advertise in its VTP domain?()
相似题目
-
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch. How would you interconnect and configure LAG for connectivity and ensure redundancy?()
-
he network administrator is trying to add Switch1 to the network, but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem?()
-
You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()
-
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch, which interface command is used to convert a Layer 3 interface to a Layer 2 interface?()
-
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?() https://assets.asklib.com/images/image2/2018073109354514482.jpg
-
When the Catalyst switch R1 is enabled to use VTP, which information does it advertise on its trunk ports?()
-
The network administrator is trying to add Switch1 to the network, but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem?()
-
Two directly connected routers, R1 and R2, are both configured for OSPF graceful restart. R2 is able to switch packets in hardware, but R1 is not. If a network administrator logs on to R2 and performs a system reload, which will be the result?()
-
VTP is configured on switch R1. Which of the following features were added in VTP version 2 that were not previously supported in VTP version 1?()
-
The network administrator is trying to add Switch1 to the network, but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem? ()
-
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?()
-
The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.0 0.0.0.255 any What is the effect of this access list configuration?()
-
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? ()https://assets.asklib.com/images/image2/2018073015150790983.jpg
-
Switch R1 is configured with VTP. Which two VTP modes will make R1 capable of creating and deleting VLANs on itself? ()
-
A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?()
-
You need to configure port security on switch R1. Which two statements are true about this technology? ()
-
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct, what will be true about Switch 15?() https://assets.asklib.com/images/image2/2018073109302428070.jpg
-
A cisco 4404 wlan controller is being connected to a cisco 6500 catalyst series switch. How would you interconnect and configure lag for connectivity and ensure redundancy?()
-
Switch R1 has been configured with the root guard feature. What statement is true if the spanning tree enhancement Root Guard is enabled? ()
-
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch. How would younterconnect and configure LAG for connectivity and ensure redundancy?()
-
When configuring a routed port on a Cisco multilayer switch, which of these is a required configuration task that you must perform to enable that port to function as a routed port? ()
-
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?()