Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?()
相似题目
-
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this? ()
-
Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? ()https://assets.asklib.com/images/image2/2018073114120422979.jpg
-
You have configured router R1 with HSRP, using the standard defaults. Which three statements are true of a default HSRP configuration?()
-
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol (HSRP)? ()
-
If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network()。
-
Which series of commands will configure router R1 for LAN-to-LAN communication with router R2? The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIP.()https://assets.asklib.com/images/image2/2018072315342863428.jpg
-
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()
-
What is the purpose of configuring router R1 with the "IP Helper address" command?()
-
Which command can be used on a PE router to connect to a CE router (11.1.1.4) in VRF red?()
-
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?()
-
R1 in ASN 1 with loopback1 address 1.1.1.1 needs to be configured with an iBGP connection to R2 with loopback2 IP address 2.2.2.2. The connection should use the loopbacks. Which o f the following commands is required on R1?()
-
请问以下配置中,R1的OSPF路由器ID是什么() R1(config)#interface s0/0/0 R1(config-if)#ip add 192.168.2.1 255.255.255.252 R1(config)#int loopback 0 R1(config-if)# ip add 10.1.1.1 255.255.255.255 R1(config)#router ospf 1 R1(config-if)#network 192.168.2.0 0.0.3.255 area 0
-
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1? ()
-
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? ()https://assets.asklib.com/images/image2/2018073010540810068.jpg
-
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2?()https://assets.asklib.com/images/image2/2018073015422145313.jpg
-
Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
-
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?()
-
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
-
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1‘s decision of what r outes to add to the IP routing table?Note that RD refers to reported distance and FD to feasible distanc E.()
-
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0".Whic h of the following is most likely to have caused this output to occur on R1?()
-
The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?()Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/DownState/PfxRcd1.1.1.1 4 1 60 61 26 0 0 00:45:0102.2.2.2 4 3 153 159 26 0 0 00:38:131
-
根据网络拓扑和需求说明,完成(或解释)路由器R1的配置。 Router(config) ipv6 unicast-routing(3)
-
Router R1 learns two routes with BGP for prefix 200.1.0.0/16. Comparing the two routes, route 1 has a shorter AS_Path Length, smaller MED, the same Weight, and smaller Local PreferencE.Which of the following is true about Router R1‘s choice of best path for this prefix?()
-
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?()