Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
相似题目
-
A new network has been configured using OSPF as the routing protocol. With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?()
-
Policy -Based Routing (PBR) has been enabled on Router R1's interfa ce F0/0. Which of the following is true regarding how PBR works?()
-
Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol (DTP) desirable mode?()
-
Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?()https://assets.asklib.com/images/image2/2018072408582679930.jpg
-
A Cisco router has been configured with the following command:IP nat pool nat-test 192.168.6.10 192.168.6.20 netmask 255.255.255.0his is an example of what type of NAT?()
-
If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network()。
-
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?()
-
Switch R1 has been configured with Private VLANs. With that type of PVLAN port should the default gateway be configured?()
-
Cisco Express Forwarding has been enabled on router TK1. With CEF, prefixes that require exception processing can be cached with one of which four special adjacencies? ()
-
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()
-
Refer to the exhibit. GLBP has been configured on the network. When the interface serial0/0/1 on router R1 goes down, how is the traffic coming from Host1 handled? () https://assets.asklib.com/images/image2/2018073015230243383.jpg
-
Inter-VLAN routing has been implemented in the Company network. In VLAN routing, what are some of the disadvantages of designing a router-on-stick configuration? ()
-
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router,as the routing protocol for the network.Which statement about thisnetwork is true?()
-
HSRP has been configured between two Company devices. What kind of message does an HSRP configured router send out every 3 seconds?()
-
A router has been configured with an EIGRP variance of 3. Which of the following statements istrue?()
-
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?()
-
Switch R1 has been configured with the root guard feature. What statement is true if the spanning tree enhancement Root Guard is enabled? ()
-
On router R1, which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command?()
-
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?()
-
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result?()
-
Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
-
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
-
A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router‘s Fa0/0 interface.Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?()
-
Router R1 learns two routes with BGP for prefix 200.1.0.0/16. Comparing the two routes, route 1 has a shorter AS_Path Length, smaller MED, the same Weight, and smaller Local PreferencE.Which of the following is true about Router R1‘s choice of best path for this prefix?()