Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.Which of the following is true about how IOS tries to limit EIGRP‘s use of bandwidth on S0/0?()
![](/upload/20220827/c85071da6ff0aadc10ebce6c25bb4f0d.png)
相似题目
-
Which router IOS commands can be used to troubleshoot LAN connectivity problems?()
-
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this? ()
-
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?()https://assets.asklib.com/images/image2/2018072410123247953.jpg
-
You have configured router R1 with HSRP, using the standard defaults. Which three statements are true of a default HSRP configuration?()
-
R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1()。
-
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol (HSRP)? ()
-
Which router or router combination is used to calculate the MPLS traffic engineering tunnel path?()
-
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? ()https://assets.asklib.com/images/image2/2018073015150790983.jpg
-
Which series of commands will configure router R1 for LAN-to-LAN communication with router R2? The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIP.()https://assets.asklib.com/images/image2/2018072315342863428.jpg
-
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()
-
Which command can be used on a PE router to connect to a CE router (11.1.1.4) in VRF red?()
-
Refer to the exhibit, Host A pings interface S0/0 on router 3, what is the TTL value for that ping?()https://assets.asklib.com/images/image2/2018072316292671645.jpg
-
请参见图示,主机A ping接口S0/0的router3,什么是该ping的TTL值?()https://assets.asklib.com/images/image2/201807231537135902.jpg
-
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?()
-
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?()
-
请问以下配置中,R1的OSPF路由器ID是什么() R1(config)#interface s0/0/0 R1(config-if)#ip add 192.168.2.1 255.255.255.252 R1(config)#int loopback 0 R1(config-if)# ip add 10.1.1.1 255.255.255.255 R1(config)#router ospf 1 R1(config-if)#network 192.168.2.0 0.0.3.255 area 0
-
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?()
-
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
-
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2?()https://assets.asklib.com/images/image2/2018073015422145313.jpg
-
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?()
-
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
-
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0".Whic h of the following is most likely to have caused this output to occur on R1?()
-
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()
-
在《规划自己的网络》实践的任务1中,为R1-ISP的S0/0/0接口分配的IP地址是多少()